Catch Basin Inserts
Curb Inlet Storm Drain Defender
The new Storm Drain Defender for Curb Inlet Drains (PATENT PENDING) is a temporary solution for Type 1 basins with a man hole cover and no grate. The insert hangs from a wire frame that is held in place in the opening by a simple support bar. This catch basin insert will trap leaves, debris, sediment and pollutants that are carried by storm water into the drainage system, reducing the amount of pollutants that enter the waterway.
Specifications
- Size: Adjusts to Curb Inlet Drain Opening; smallest 22”; largest 26”
- Material: 8 oz Polypropylene, Non-Woven Geotextile Fabric. 8 gage wire frame with 3’ piece of 5/16” deformed wire support bar.
- Flow Rate: Maximum overflow rate varies depending on the level of soil that has accumulated with the fabric. Proper maintenance is mandatory to maintain maximum water flow.
- The STORM DRAIN DEFENDER has overflow outlets to allow excessive water during heavy rain showers to bypass the system, reducing the chance of flooding or ponding. Also, during high flow rates, water may bypass this insert by flowing over the back of the insert.
- Removes: Oil, Grease, Sediment, Litter, Debris
- Disposal: Disposal is dependent on nature of pollutants being collected. Disposal should be in accordance to local, state and federal regulations.
- Weight: Empty = STORM DRAIN DEFENDER units are approx. 3 lbs. Full = Weight of empty unit plus weight of sediment and water trapped in unit. Dry sediment could weigh 25-40 pounds. Fully loaded, wet units can weigh approximately 50-85 pounds.
| Storm Drain Defender | Curb Inlet |
| Product # | DDCI |
| Weight | 3 lbs |
| Price Each | $55.00 |
Storm Drain Defender – Round
Storm water runoff carries with it dirt and hydrocarbons that pollute our downstream supplies. The STORM DRAIN DEFENDER traps these pollutants, reducing and controlling the entrance of contaminants into our water systems.
The STORM DRAIN DEFENDER – U.S. Patent No. 7,201,843 – is a simple sheet of geotextile fabric supported by a wire frame. The standard round models adjust to fit round drains size 27″ – 29″ in diameter. The entire unit is under the grate, no excess fabric extends above the grate, creating a safer environment for pedestrians. No trimming required.
| Storm Drain Defender U.S. Patent No. 7,201,843 |
Sediment Only | With Oil Pillow | Trash & Debris |
| Product # | DDSED-RND | DDRND-WPIL10 | DDRND-TRSH |
| Weight | 2 lbs | 5 lbs | 2 lbs |
| Price Each | $54.00 | $62.00 | $54.00 |
Specifications:
- Size: Round—Adjusts from 27” to 29” diameter. The single fabric sheet is 4’x5’. The depth varies, depending on the size of the drain and how deep the fabric hangs down.
- Material: Standard Fabric—8 oz Polypropylene, Non-Woven Geotextile Fabric
- Trash Units—High Density Polyethylene Tarp Screening
- Flow Rate: Maximum overflow rate varies depending on the level of debris and sediment that has accumulated in the fabric. Proper maintenance is mandatory to maintain maximum water flow.
- The STORM DRAIN DEFENDER units have overflow outlets to allow excessive water during heavy rain showers to bypass the system, reducing the chance of flooding or ponding.
- Removes: Oil, Grease, Sediment, Litter, Debris
- Disposal: Disposal is dependent on nature of pollutants being collected. Disposal should be in accordance with local, state and federal regulations.
- Weight: Empty = STORM DRAIN DEFENDER units are approx. 2—3 lbs. Full = Weight of empty unit plus weight of sediment and water trapped in unit. Dry sediment could weigh 30-50 pounds. Fully loaded, wet units can weigh approximately 85-135 pounds.
Sediment Only Unit
Trap Pollutants
Mesh Fabric-Trash Unit
Storm Drain Defender-Rectangle
Storm water runoff carries with it dirt and hydrocarbons that pollute our downstream supplies. The STORM DRAIN DEFENDER traps these pollutants, reducing and controlling the entrance of contaminants into our water systems.
The STORM DRAIN DEFENDER – U.S. Patent No. 7,201,843 – is a simple sheet of geotextile fabric supported by a wire frame. Size is adjustable to fit a variety of drain sizes. The entire unit is under the grate, no excess fabric extends above the grate, creating a safer environment for pedestrians. No trimming required.
| Storm Drain Defender U.S. Patent No. 7,201,843 |
Sediment Only | With Oil Pillow | Trash & Debris |
| Product # | DDSED-REC | DDREC-WPIL10 | DDREC-TRSH |
| Weight | 2 lbs | 5 lbs | 2 lbs |
| Price Each | $54.00 | $62.00 | $54.00 |
Specifications:
- Size: Rectangular —Adjusts to fit Drains; smallest 16”X20”; largest 28”X36”The single fabric sheet is 4’x5’. The depth varies, depending on the size of the drain and how deep the fabric hangs down.
- Material: Standard Fabric—8 oz Polypropylene, non-woven geotextile fabric
- Trash Units—High Density Polyethylene Tarp Screening.
- Flow Rate: Maximum overflow rate varies depending on the level of debris and sediment that has accumulated in the fabric. Proper maintenance is mandatory to maintain maximum water flow.
- The STORM DRAIN DEFENDER units have overflow outlets to allow excessive water during heavy rain showers to bypass the system, reducing the chance of flooding or ponding.
- Removes: Oil, Grease, Sediment, Litter, Debris.
- Disposal: Disposal is dependent on nature of pollutants being collected.
- Disposal should be in accordance with local, state and federal regulations.
- Weight: Empty = STORM DRAIN DEFENDER units are approx. 2—3 lbs. Full = Weight of empty unit plus weight of sediment and water trapped in unit. Dry sediment could weigh 30-50 pounds. Fully loaded, wet units can weigh approximately 85-135 pounds.
Easy Installation
Optional Oil Pillow
Mesh Fabric-Trash Unit